Menu
Your Cart

DOUBLE SIDED WOOL BUFF 9' 230MM WITH 5/8 THREAD

DOUBLE SIDED WOOL BUFF 9' 230MM WITH 5/8 THREAD
DOUBLE SIDED WOOL BUFF 9' 230MM WITH 5/8 THREAD
  • Stock: In Stock
  • Brand: TORK CRAFT
  • Model: MM DS9-2
  • Weight: 0.36kg
  • Dimensions: 335.00mm x 270.00mm x 50.00mm
  • SKU: MM DS9-2
  • UPC: 6009515827823
R 697.88
Ex Tax: R 606.85
Double sided wool buff

Diameter: Ø230mm
Thread/Hook & Loop: 5/8 UNC

 Application:

The double sided wool buff should be used with an automotive polisher. Different compounds, polishes and waxes can be applied to both sides of the buff and then flipped around when needed. This saves time without the need of changing to another buff.

It is necessary to polish a vehicle body panel when:

  • The panel has been newly painted with a clear-coat.
  • Shallow scratch marks need to be removed.
  • The panel has suffered from oxidation.
  • Swirl marks and hologram defects need to be removed.

TIP:
The buff is washable after use if the compound is soluble.

Double sided wool buff range:

ORDER NO. DIAMETER THREAD
MM DS7 Ø180mm M14
MM DS7-2 ø180mm 5/8 UNC
MM DS9 ø230mm M14
MM DS9-2 ø230mm 5/8 UNC

Adaptors to convert or lenghten the polisher's thread:

ORDER NO./td> MALE THREAD FEMALE THREAD
SPC00055 5/8 UNC 5/8 UNC
SPC00053 5/8 UNC M14
SPC00054 M14 5/8 UNC
SPC00052 M14 M14
Double sided wool buff

Steps to take when polishing a panel:

1. Preparing the panel:

  • Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
  • The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
  • Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.

2. Applying the polishing compound:

  • A five rand coin amount of polishing compound should be applied to the sponge. Switch the polisher to it's lowest speed setting.
  • Switch on the polisher and gradually spread the polishing compound over the panel.
  • Keep moving the polisher on the panel to have as little amount of pressure and friction.
  • The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
  • Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.

3. Wash the panel when finished:

  • Wash the panel after polishing to remove any residue from the polishing compound.
consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

Write a review

Note: HTML is not translated!
Bad Good
This is the sticky Notification module. You can use it for any sticky messages such as cookie notices or special promotions, etc.