Name: POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY
Brand: TORK CRAFT
SKU: POL02
Price: 2309.49 ZAR
Availability: InStock

POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY

Stock: In Stock
Brand: TORK CRAFT
Model: POL02
Weight: 3.26kg
Dimensions: 142.00mm x 450.00mm x 450.00mm
SKU: POL02
UPC: 6009515828516

Based on 0 reviews. - Write a review

R 2,309.49

Ex Tax: R 2,008.25

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Polisher

Wattage: 1200W
No load speed: 1100-3500 RPM

Supplied with a ø180mm wool bonnet buff and backing pad.

Application:

The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface.

The objective of polishing is to remove imperfections in the clear-coat that cause the paint to look dull. Surface imperfections can include swirls, scratches, water spots, etchings, industrial fallout, oxidation, etc.

Features:

Professionally manufactured for the automotive paint care and detailing industries.
Ergonomically designed to reduce fatigue in long term use.
The polisher has various hand-held positions to better hold the polisher at angles.
Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher.

The polisher range:

ORDER NO.	DESCRIPTION	WARRANTY
POL01	Polisher, 800W. Supplied with ø125mm wool buff	6 Months
POL02	Polisher, 1200W. Supplied with ø180mm wool buff	6 Months
POL03	Polisher, 1700W. Supplied with ø180mm sponge pad	6 Months

The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it's lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down.

Spare parts for the POL02 polisher:

ORDER NO.	DESCRIPTION
POL02-12	Big gear
POL02-13	Bearing
POL02-16	Aluminium head
POL02-19	Fixation knob
POL02-24	Armature
POL02-29	Field coil (stator)
POL02-30	Motor housing
POL02-33	Carbon brushes
POL02-37-38	Speed control (switch)
POL02-40	Rear handle
POL02-46	Trigger switch

Polisher

Steps to take when polishing a panel:

1. Preparing the panel:

Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.

2. Applying the polishing compound:

A five rand coin amount of polishing compound should be applied to the buff. Switch the polisher to it's lowest speed setting.
Switch on the polisher and gradually spread the polishing compound over the panel.
Keep moving the polisher on the panel to have as little amount of pressure and friction.
The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.

3. Wash the panel when finished:

Wash the panel after polishing to remove any residue from the polishing compound.

consider safety for your health and the people around you
General safety suggestions: It is advisable to always have the following items nearby and in a good condition Eye protection – clean and scratch free Hearing protection – quality earmuffs Dust masks – discard old and dirty masks Gloves – for easy handling of material and hand protection

Wear Gloves	Eye Protection	Hearing Protection	Dust Mask