Menu
Your Cart

POLISHING SPONGE HOOK AND LOOP 125MM 5'

POLISHING SPONGE HOOK AND LOOP 125MM 5'
POLISHING SPONGE HOOK AND LOOP 125MM 5'
  • Stock: In Stock
  • Brand: TORK CRAFT
  • Model: SPC00124
  • Weight: 0.03kg
  • Dimensions: 220.00mm x 150.00mm x 25.00mm
  • SKU: SPC00124
  • UPC: 6009515825201
R 141.68
Ex Tax: R 123.20
Compounding sponge

Pattern: Standard
Density: Firm
Colour: Blue
Diameter: Ø125mm
Thread/hook and loop: hook and loop

 Application:

The compounding sponge should be used with an automotive polisher.

It is necessary to polish a vehicle body panel when:

  • The panel has been newly painted with a clear-coat.
  • Shallow scratch marks need to be removed.
  • The panel has suffered from oxidation.
  • Swirl marks and hologram defects need to be removed.

Compounding sponge uses:

COLOUR POLISH COMPOUND
White Good Best
Orange Good Best
Red Best  
Black Best  

Compounding sponge range:

ORDER NO. DENSITY COLOUR DIAMETER THREAD PATTERN
SPC00101 Firm Orange ø200mm Hook & Loop Standard
SPC00100 Soft Yellow ø200mm Hook & Loop Standard
SPC00102 Soft Red ø200mm Hook & Loop Standard
TCCS15058 Firm White ø150mm 5/8 UNC Standard
TCCS15014-1 Firm White ø150mm M14 Standard
TCCS15014-4 Firm White ø150mm M14 Standard
TCCS15014 Firm Orange ø150mm M14 Standard
TCC15014-2 Soft Red ø150mm M14 Standard
TCCS15014-3 Soft Black ø150mm M14 Standard
TCCS15014-5 Soft Black ø150mm M14 Waffle
SPC00124 Firm Blue ø125mm Hook & Loop Standard

NOTE:
For the ø200mm Hook & Loop compounding sponges, use the M14 backing pad SPC00106.

Adaptors to convert or lenghten the polisher's thread:

ORDER NO./td> MALE THREAD FEMALE THREAD
SPC00055 5/8 UNC 5/8 UNC
SPC00053 5/8 UNC M14
SPC00054 M14 5/8 UNC
SPC00052 M14 M14
Compounding sponge

Steps to take when polishing a panel:

1. Preparing the panel:

  • Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
  • The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
  • Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.

2. Applying the polishing compound:

  • A five rand coin amount of polishing compound should be applied to the sponge. Switch the polisher to it's lowest speed setting.
  • Switch on the polisher and gradually spread the polishing compound over the panel.
  • Keep moving the polisher on the panel to have as little amount of pressure and friction.
  • The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
  • Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.

3. Wash the panel when finished:

  • Wash the panel after polishing to remove any residue from the polishing compound.
The compounding sponge should be used with an automotive polisher.
consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

Write a review

Note: HTML is not translated!
Bad Good
This is the sticky Notification module. You can use it for any sticky messages such as cookie notices or special promotions, etc.